Home » Project Material » Construction Of A Battery Changer Using Silicon Controlled Regulator SCR

Construction Of A Battery Changer Using Silicon Controlled Regulator SCR

5 Chapters
|
33 Pages
|
4,212 Words
|
Electrical Electronics Engineering

Complete Construction Of A Battery Changer Using Silicon Controlled Regulator SCR Project Materials (Chapters 1 to 5):

ABSTRACT

The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories.
This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed cover the construction of battery charger for battery sizes ranging from 6 voltage to 24volatge (heavy duty) batteries.
The prototype of a battery charger for these ranges of batteries has been implemented following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory. adequate care has been taken in the design and construction to ensure that the resultant battery charger are both reliable and easy to use.

TABLE OF CONTENT

Title Page
Approval Page
Dedication
Acknowledgement
Abstract

 

Chapter One
1.0 Introduction

1.1 Background Of The Project
1.2 Aim And Objective
1.3 Scope Of The Project
1.4 Organization Of The Project

Chapter Two
2.0 Literature Review

2.1 Battery
2.2 The Storage Battery
2.2.1 Nikel Iron Battery
2.2.2 Lead Acid Battery
2.3 Indications Of A Fully Charged Cell
2.3.1 Gassing
2.3.2 Voltage
2.3.3 Colour
2.3.4 Charger

Chapter Three
3.1 Function Block Diagram

3.1.1 Power Supply Unit
3.1.2 Ac To Dc Rectification
3.1.3 Filter And Regulation
3.2 Types Of Carrging System
3.2.1 Half Wave System
3.2.2 Full Wave Charging System

Chapter Four
4.1 Construction Of Battery Charger

4.1.1 Power Supply Unit (Psu)
4.1.2 Detector Circuit
4.2 Components Of A Psu
4.3 Components Of Detector Circuit

Chapter Five
5.1 Summary

5.2 Conclusion
5.3 Component Sourcing
References

CHAPTER ONE

1.0 INTRODUCTION
In our society today writing a project is all about applying the theories learnt over the year to produce design and construct and operating system which will be capable of performing a known task.
It is from this point of view that I decoded to write, design and construct this particular project which has the titles construction of a battery charger using SCR (Silicon controlled regulator).
A battery charger is an electric device employed in charging batteries the batteries. The batteries that are usually charged by battery charges are the storage batteries also known as accumulators.

1.1 BACKGROUND OF THE PROBLEMS
The charger is made up of various electrical and electronics components which for purpose of clarity are grouped into four basic units. They are the power supply unit the smoothening circuit the regulatory unit and the regulated direct current (d.c) charging unit.

1.2 AIM AND OBJECTIVE OF THE PROJECT
The aim and objective of this project is to highlight and design how to use SCR to charger batteries. Battery charger been constructed in many different ways but the silicon control regulated type is more sensitive than the ordinary battery charger. This is because it has the ability to indicate or detect full charging of a cell the detector or indicator light will automatically lights up when the battery attains a fully charged cell.

1.3 SCOPE OF THE PROJECT
Battery charger comes in various design voltages and wattages the choice of a particular kind of charger then depends largely on the size of battery or batteries which one intends to charge the miniature battery charger could be needed to charge one battery whose voltage ranges form 6-12voltage the bigger charger are for batteries with voltages ranging from 12-48 voltage. These are the heavy duty batteries. The battery charger that I am about to construct will successfully charge a battery of 250MA or an equivalent 6-12 volts batteries.

1.4 ORGANIZATION OF THE PROJECT
The proceeding chapter of this project is all about the literature review of this project and the indications of a fully charged cell. Chapter three explains the functional block diagram types of charging system. The construction of this project is all stated in detail in chapter four of this report chapter five outlines the summary conclusion component sourcing and references.

You Might Like These:
Project Structure

The introduction of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should start with the relevant background information of the study, clearly define the specific problem that it addresses, outline the main object, discuss the scope and any limitation that may affect the outcome of your findings

Literature Review of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should start with an overview of existing research, theoretical framework and identify any gaps in the existing literature and explain how it will address the gaps

Methodology of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should describe the overall design of your project, detail the methods and tools used to collect data explain the techniques used to analyse the collected data and discuss any ethical issues related to your project

Results should include presentation of findings and interpretation of results

The discussion section of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should Interpret the implications of your findings, address any limitations of your study and discuss the broader implications of your findings

The conclusion of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should include summarize the main results and conclusions of your project, provide recommendations based on your findings and offer any concluding remarks on the project.

References should List all the sources cited in Construction Of A Battery Changer Using Silicon Controlled Regulator SCR project by following the required citation style (e.g., APA, MLA, Chicago).

The appendices section should Include any additional materials that support your project (Construction Of A Battery Changer Using Silicon Controlled Regulator SCR) but are too detailed for the main chapters such as raw data, detailed calculations etc.