Design And Fabrication Of Chin-Chin Cutting Machine
Complete Design And Fabrication Of Chin-Chin Cutting Machine Project Materials (Chapters 1 to 5):
Cutting is a major operation in food processing. It is time consuming and labour intensive. In Nigeria and most developing countries, it is normally done manually with the exception of a few processing factories where some imported equipment are used. In this study, a low cost motorized, table, rotary chin chin cutting machine was designed and fabricated using locally available materials to solve the problems associated with cutting of agricultural and food products in Nigeria. The machine consists of a feeding compartment, cutting compartment, power transmission and outlets. It was designed for cutting chin-chin. The machine has a throughput of 37.8 g/s. The maintenance of the machine is simple and recommended for small holders, local processors and home use.
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 AIM OF THE PROJECT
1.2 OBJECTIVE OF THE STUDY
1.3 PURPOSE OF THE PROJECT
1.4 JUSTIFICATION OF THE PROJECT
1.5 APPLICATION OF THE PROJECT
1.6 SIGNIFICANCE OF THE STUDY
1.7 LIMITATION OF THE STUDY
1.8 PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
2.1 OVERVIEW OF CHINCHIN
2.2 REVIEW OF THE RELATED CUTING MACHINES
2.3 REVIEW OF EXISTING CHINCHIN CUTTER
CHAPTER THREE
3.1 MATERIALS AND METHODS
3.2 DESIGN REQUIREMENTS FOR THE CHINCHIN CUTTING MACHINE
3.3 MATERIAL SELECTION FOR COMPONENT PARTS OF THE MACHINE
3.4 DESIGN ANALYSIS OF COMPONENT PARTS OF THE CHINCHIN MACHINE
3.5 MEASURES TO BE TAKEN PRIOR TO
CHAPTER FOUR
4.1 RESULTS AND DISCUSSION
CHAPTER FIVE
5.1 CONCLUSION
5.2 REFERENCES
1.1 INTRODUCTION
Chin Chin is a fried snack from West Africa and is nowadays very popular in many places around the world. It is a crunchy fried dough of wheat flour and some other baking ingredients. In West Africa, Chin Chin usually contains cowpeas flour, and ground nutmeg is often added for flavor.
In Nigerian homes, restaurants, outdoor catering services and snacks centers, cutting operation is usually carried out manually. It is energy and time consuming, tedious, a high risk and back straining operation. Developing a rotary cutter locally will make cooking at home, outdoor catering and confectionaries easier with good quality products. Also time and energy will be conserved for other useful purpose.
Although advance in technology is rendering some people unemployed, but its somehow not so bad considering time factor. People in the business of chin-chin production complaining of how slow it takes their employees to level the raw chin chin and cut it to shape before frying it. Here is your solution, the chin-chin cutting machine, this machine is in two section, the first section saves you the time of levelling the raw chin chin and the second section cuts both horizontally and vertically giving you the perfect shape depending on the adjustment given to the cutting blade.
1.2 AIM OF THE PROJECT
The aim of this research is to develop a rotary cutter for cutting fresh/ wet vegetables, confectionary and fruits for small scale food processing.
1.3 OBJECTIVE OF THE PROJECT
The project research objectives are:
i. To construct a local fabricated chin-chin cutting machine using available local technology.
ii. To construct a machine with a size specification.
iii. To construct a machine which can perform a domestic operations.
iv. To construct a machine which has adequate capacity, lighter in weight, lesser fatigue and portable.
1.4 PURPOSE OF THE PROJECT
This project is meant to achieve the following purpose
1) To design and fabricate chin-chin cutting machine which easy to operate with high degree of efficiency
2) To design and fabricate a machine (chin-chin cutting machine) that would save time and cost, with high degree of production volume.
3) To design and construct a chin-chin cutting machine that would not have much breaking effect of chin chin during the process.
4) To design and construct a chin-chin cutting machine that is economical and have little or no complication in maintenance
5) To design and construct a chin-chin cutting machine with high percentage at local technology
6) To design and construct a machine that is cost effective and manual stress reduction
7) To have a neat, well-shaped and fast means of producing chin-chin
1.5 JUSTIFICATION OF THE PROJECT
i. This is to promote indigenous machine and their producers.
ii. To have a portable chin-chin cutting machine constructed for domestic uses with a powered driven source.
iii. To improve the economic and the country as a whole by neglecting imported chin-chin cutting machine.
1.6 APPLICATION OF THE PROJECT
This machine is used in homes, restaurants, outdoor catering services and snacks centers. This machine is used for cutting:
i. vegetables,
ii. fruits
iii. confectionaries like chin-chin
iv. and salad ingredients
1.7 SIGNIFICANCE OF THE PROJECT
-It can cut far more than just chin-chin.
-It doesn’t heat up the chin-chin like other wheat machine can.
-It doesn’t spew chin-chin anywhere.
-This machine saves both cost and time.
1.8 LIMITATION OF THE PROJECT
The limitations of this project are:
i. It cost of production can be higher for students
ii. It’s noisy.
iii. The capacity of the hopper is smaller than other heavy-duty mills. You would need to fill the hopper more frequently than mills with a larger capacity.
1.9 PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work, chapter two presents the literature review of the study, chapter three describes the methods applied, chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.
The introduction of Design And Fabrication Of Chin-Chin Cutting Machine should start with the relevant background information of the study, clearly define the specific problem that it addresses, outline the main object, discuss the scope and any limitation that may affect the outcome of your findings
Literature Review of Design And Fabrication Of Chin-Chin Cutting Machine should start with an overview of existing research, theoretical framework and identify any gaps in the existing literature and explain how it will address the gaps
Methodology of Design And Fabrication Of Chin-Chin Cutting Machine should describe the overall design of your project, detail the methods and tools used to collect data explain the techniques used to analyse the collected data and discuss any ethical issues related to your project
Results should include presentation of findings and interpretation of results
The discussion section of Design And Fabrication Of Chin-Chin Cutting Machine should Interpret the implications of your findings, address any limitations of your study and discuss the broader implications of your findings
The conclusion of Design And Fabrication Of Chin-Chin Cutting Machine should include summarize the main results and conclusions of your project, provide recommendations based on your findings and offer any concluding remarks on the project.
References should List all the sources cited in Design And Fabrication Of Chin-Chin Cutting Machine project by following the required citation style (e.g., APA, MLA, Chicago).
The appendices section should Include any additional materials that support your project (Design And Fabrication Of Chin-Chin Cutting Machine) but are too detailed for the main chapters such as raw data, detailed calculations etc.