Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete
INSTRUCTIONS:
- You are perusing the project material titled “Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete.”
- The project material on Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete is available for instant download.
- Preview Chapter One of Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete at no cost.
- To access the complete project material for Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete, kindly make a donation to support the ongoing maintenance and operation of this website.
- The provided work on Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete is intended solely for academic research purposes and should be utilized strictly as a set of guidelines.
- Our objective in distributing Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete is to aid individuals unfamiliar with project research, specifically writers seeking assistance in this area.
- Kindly refrain from directly replicating the content provided in Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete materials.
- Feel free to reference “Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete” in your work, provided that you paraphrase appropriately.
- Unauthorized reproduction of Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete content is prohibited under our Terms of Use.
- UniProjects assumes no responsibility if you replicate the content of this Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete.
Table of contents
Contents                                                             Page
Title page
Certification                                                                  i
Dedication                                                                    ii
Acknowledgment                                                          iii
Table of contents                                                          iv
List of Tables                                                                viii
List of Plates                                                                 ix
List of figure                                                                 x
Abstract                                                                        xi
CHAPTER ONEÂ
1.0    Introduction                                                                  1
1.1    Statement of the problem                                   3
1.2    Aim and objectives                                              4
1.3    Justification of the study                                              5
1.4    Scope and limitation of the work                        5
1.5    Methodology                                                       6
CHAPTER TWO
2.0    Review of literature                                             7
2.1    Ingredient of concrete                                          9
2.1.1 Water                                                                            9
2.1.2 Aggregates                                                          10
2.1.3 Cement                                                                11
2.1.4 Admixtures                                                         12
2.2    Bamboo leaf ash                                                 14
2.3    Properties of concrete                                         15
2.3.1 Fresh concrete                                                     15
2.3.2 Hardened concrete                                                        16
2.4    Factors affecting strength of concrete                           18
CHAPTER THREE
3.0    Materials and methods                                        21
3.1    Material selection                                                          21
3.1.1 Coir Ash                                                             21
3.1.2 Coarse aggregate                                                 23
3.1.3 Fine aggregate                                                     23
3.1.4 Cement                                                                23
3.2    Test of the constituent materials                                   23
3.2.1 Proportioning                                                      24
3.2.2 Batching                                                              24
3.2.3Â Composition of the constituent materials
for the production of concrete                                      25
3.2.3 Mixing                                                                 27
3.2.4 Casting                                                                28
3.2.5 Compaction                                                                  29
3.2.6 Curing                                                                 29
3.2.7 Crushing                                                             30
3.3    Experimental Investigation                                 31
3.3.1 Laboratory Test                                                  31
3.3.1.1 Sieves Analysis                                                31
3.3.1.2 Slump Test                                                      33
3.3.1.4 Compressive strength of concrete                    34
CHAPTER FOUR
4.0    Results and Discussion                                                36
4.1Â Â Â Â Result of the Sieve analysis
(Particle Size Distribution)Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â 36
4.2    Workability (Slump) Test                                   40
4.3    Density Test                                                                 40
4.4Â Â Â Â Compressive Strength of the Hardened
Concrete Cubes                                                   44
4.5    Discussion of Result                                           45
CHAPTER FIVE
5.0    Conclusion and Recommendation                       50
5.1    Conclusion                                                          50
5.2    Recommendation                                                51
Reference                                                             52
LIST OF PLATES
Plate: 3.1   Bamboo Leaf in it Natural Habitat                      21
Plate:3.2Â Â Â Â Burning of Bamboo Leaf (BLAsh)Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â 22
Plate 3.3    Sieve Analysis Test on BLAsh                                     22
Plate 3.4Â Â Â Â Mixing of Bamboo Leaf Ash with
Varying % of Cement, Fine Aggregate
and Coarse Aggregate                                         27
Plate: 3.5Â Â Â Casting of Concrete Cubes with
BLAsh Replacements                                          28
Plate 3.6    Curing of Concrete Cubes                                   29
Plate 3.7    Compressive Strength Test on the Concrete Cubes      30
Plate 3.8    Slump of Test of BLAsh Concrete                               33
LIST OF TABLE
TABLE 3.1 COMPOSITION OF CONSTITUTENT
material for BLAsh concrete
at 0%,5%,10%,15% and 20% case            27
Table 4.1   The particle size distribution of sharp sand        36
Table 4.2   The Particle Size Distribution of Granite   39
Table 4.3   The Slump Value of The Fresh Concrete   40
Table 4.4Â Â Â the Density of the Hardened Concrete
after 7 Days of Curing                             41
Table 4.5Â Â Â the Density of the Hardened Concrete
after 14 Days of Curing                             41
Table 4.6Â Â Â The Density of the Hardened Concrete
after 21 Days of Curing                             22
Table 4.7Â Â Â The Density of the Hardened Concrete
after 28 Days of Curing                             43
Table 4.8   The Average Density of the Hardened Concrete 43
Table 4.9Â Â Â Compressive Strength of the Hardened
Concrete after 7 Days                                44
Table 4.10Â Compressive Strength of the Hardened
Concrete after 14 Days                              45
Table 4.11Â Compressive Strength of the Hardened
Concrete after 21 Days                              46
Table 4.12Â Compressive Strength of the Hardened
Concrete after 28 Days                              47
Table 4.13Â Average Compressive Strength of
BLAsh Concrete at different Ages             28
LIST OF FIGURE
Figure 4.1  Particle Size Distribution Curve of Sharp Sand  37
Figure 4.2  Particle Size Distribution Curve of Granite                  39
Figure 4.3Â Â Effects of BLAsh Replacement on
Concrete with respect to Days Curing                          48
ABSTRACT
Concrete is a major construction material, which is usually made by mixing cement, water, fine and coarse aggregate and sometimes admixtures in their right proportions. The use of waste materials with pozzolanic properties in concrete production is a becoming a worldwide practice. The assessment of the pozzolanic activity of cement replacement materials is becoming increasingly important because of the need for more sustainable cementing products. In this bamboo leaf Ash is used as partial replacement for cement in ranges of 5%, 10% 15%. Strength and durability tests were carried out to assess the feasibility of using bamboo leaf ash as partial replacement of cement in concrete.
This showed that BLAsh has no significant effect on the density of the concrete comparatively. The strength values at different ages for BLAsh replacements compare to be a bit favorable with the control of 0% BLAsh replacement. The optimum compressive strength of 20.00N/mm2 was obtained at 5% replacement at 28 days of age compared to the control of 20.00N/mm2. It is therefore advisable to use 5% replacement of BLAsh with cement paste when it is to be used as supplement to cement.
CHAPTER ONE
- INTRODUCTION
Concrete is a composite element consisting of aggregates enclosed in a matrix of cement paste including possible pozzolanic, has two major components-cement paste and aggregates. As a construction material, concrete can be in almost any shape desired, and once hardened, can become a structural (load bearing) element. The strength of concrete depends upon the strength of these components, their deformation properties, and the adhesion between the paste and aggregate surface. With most natural aggregates, it is possible to make concrete up to 120KN/mm2 a compressive strength by improving the strength of the cement paste, which can be controlled through the choice of water-cement ratio, and type and dosage of admixtures (Dwivedi 2006).
The high cost of conventional construction material is a dominating factor affecting housing system around the world. This has necessitated research work into alternative materials in the construction field. Since the cost of cement is many times more than the cost of other ingredients in concrete making. Recently, attention is mainly directed to use of as little cement as possible constituent with adequate strength and durability. Little research has been carried out to study the bamboo leaf waste as a pozzolanic material. Dwivedi (2006) reported the reaction between calcium hydroxide (CH) and bamboo leaf ash for four hours of reaction using the differential scanning calorimetric (Dsc) technique. Singh et al (2000) discussed that eco friendly composite cements may be obtained by partial replacement of Portland cement (PPC) with low cost materials. They studied the hydration of bamboo leaf ash in a blended Portland cement. It was concluded that bamboo leaf ash is an effective pozzolanic materials. When 20 weight (wt) % of bamboo ash was mixed with PPC the compressive strength values of mortars at 28 day of hydration were found to be quiet comparable to those of PPC. Villar-cocina et al (2010) conducted a study on sugarcane leaf ash (SCLA). Hydration of 10 wt % SCLA composite Portland cement was studied by using powder x-ray diffraction, FTIR spectroscopy, and differential scanning calorimetric and other techniques. The result have show that the pozzolanic reaction of sugarcane leaf ash increases with time. They have been used to produce concrete having almost the same behavior as normal concrete.
In general, a pozzolanic material has little or no cementing properties. However, when it has a fine particle size, in the presence of moisture it can react with calcium hydroxide at ordinary temperatures to provide the cementing property. Bamboo leaf ash (BLAsh) is one of the agro waste ashes whose chemical composition contains a large amount of silica and has high potential to be used as a cement replacement (Okere 2013). Most of the concrete produced today are a multi component product containing one or more admixtures in addition to the four basic components which is cement, fine aggregate, coarse aggregate and water. For every component, one usually as several choices that could influence the cost of the end product and its behavior in service. Among the constituent components, however, cement or cementitious materials as a whole, play a vital role in producing strong and durable concrete. Utilization of these waste materials is a partial solution to environmental and ecological problems. Use of these also helps in reducing the cost of concrete production by reducing the quantity of cement used. Consequently, this study presents the suitability of using bamboo leaf ash (BLAsh) as a supplementary cementitious material. This work then investigates the effect of bamboo leaf Ash on the workability of fresh concrete and the compressive strength of added concrete.
1.1Â Â Â Â STATEMENT OF THE PROBLEM.
Concrete plays an important role in the beneficial use of the material in construction industry. Many modifications and developments have been made to place material like Bamboo Leaf Ash (BLAsh), wood wool, rice husk and marble powder as a cement replacement constituent, but it as an alternative to reveal that the replacement of Bamboo Leaf Ash (BLAsh), in Portland cement affect the compressive strength of concrete. One of the main goal of sustainable waste management is to maximize recycling and reuse. With increasing environmental pressure to reduce waste and pollution and to recycle as much as possible, the concrete industry has begun adopting a number of methods to achieve these goals.
One of the suggestions in the forefront has been the sourcing, development and use of alternative, non-conventional local construction materials including the possibility of using some agricultural wastes and residues as partial or full replacement of conventional constructional materials. In countries where abundant agricultural wastes are discharged, these wastes can be used as potential material or replacement material in construction industries.
This has a significant impact by reducing the amount of quarrying and landfill space required, and acts as a cement replacement, reduces the amount of cement of required to produce a solid concrete. As cement production creates massive quantities of carbon dioxide, cement replacement technology such as this will play an important role in future attempts to cut carbon dioxide emissions and production of economical optimum strength concrete, so as to encourage the use of this ‘impressive’ waste product as construction material in low-cost housing.
- AIM AND OBJECTIVES
The aim of this project is to study the compressive strength of concrete with cement partially replaced with bamboo leaf ash and the suitability of the material to be used as cement substitute
The objectives of the projects are:
- To determine the percentage of BLAsh as a replacement for cement of 5%,10%,15%,20%.
- To replace cement with known percentage of bamboo leaf ash and cast with it.
- To examine the workability of the fresh BLAsh concrete by slump test.
- To compare the strength of cubes cast at 100% of cement with cubes replaced with the known percentage of bamboo leaf.
- To suggest the use of bamboo leaf ash as alternative supplement to cement so as to reduce cost of construction.
1.3Â Â Â Â JUSTIFICATION OF THE STUDY.
In Nigeria today, an appreciable percentage of the entire population cannot afford to build their own houses especially modern types due to high cost of cement and the average percentage of the country’s population find it difficult or almost impossible to afford the cost. In order to curb this act, this project is targeting whether bamboo leaf ash can be used as a partial replacement for cement in order to achieve optimum strength and economic concrete and the corresponding quantity of coir ash required.
- SCOPE AND LIMITATION OF WORK
This study concentrated on investigation of compressive strength of bamboo leaf (BLAsh) concrete and pure cement (100% of cement) as a control sample. The Laboratory Tests include sieve Analysis, specific gravity natural moisture content and water absorption of each aggregate sample. Each samples of concrete were design for grade 20 (as mix ratio 1:2:4) and water cement ratio (w/c) of 0.55. The control sample composed of 100% cement, fine Aggregate, coarse aggregate and water. Then, other four samples were of the same mix design with bamboo leaf ash as cement replacement that serves as an
Unconventional mixes which comprises of 5%, 10%,15% and 20% of the total weigh of ordinary Portland cement. These specimens (samples) were the comprehensive strength test with the use of Universal Testing Machine in accordance with BS1881:Part1:1983.
In carrying out of the research work, the method adopted is in this sequence.
- Procurement of materials.
- Preparation of the bamboo leaf Ash.
- Testing of the materials.
- Casting of the cubes.
- Curing of the cubes.
- Testing for the compressive strength of the specimen.
CHAPTER FIVE
5.0Â Â Â Â CONCLUSION AND RECOMMENDATION
5.1Â Â Â Â CONCLUSION
Based on the experimental investigations carried out and results obtained, it is therefore concluded that;
- The suitability of using bamboo leaf ash BLA as supplementary cementatious material has been explored.
- The compressive strength or ability of fresh bamboo leaf ash content measured by the slump test reduces as the bamboo leaf ash content increases. It is therefore noticed, that bamboo leaf ash concrete will be workable but not as cement which is in correspondence to (ASTM C 143 or EN 12350).
- The effect of bamboo leaf ash replacement and curing on the concrete density was investigated. But the result show almost similar. This implies that the bamboo leaf ash has no significant effect on the density of the concrete comparatively.
- The compressive strength of the BLA concrete at the end of 28 days at 9%, 5%, 10% 15% and 20% BLA replacement of cement are relatively close with respect to what the control compressive strength indicated from (compressive strength of concrete classes c14 – c35). This show that the BLA can be used optimally as supplementary cementious material in concrete works.
5.2Â Â Â Â Â Â Â Â Â Â Â Â Â RECOMMENDATIONS
Based on the investigation carried out and conclusion drawn, it is therefore recommended that, to improve on the research work with more reliable results:
- For an optimum compressive strength of concrete to be obtained, at 5% replacement of cement with bamboo leaf ash is recommended
- Prior to preparing the bamboo leaf ash, more economical and reduced labour means should be adopted.
- In the coming future, recycling of waste materials in a more useful way like this should be encouraged by government and any organization with viable programs and adequate funds to encourage interested researchers to venture into it.
If you’re referencing specific information, quotes, or ideas from “Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete”, provide a citation in the appropriate format such as APA, MLA, or Chicago.
The title page of downloaded document contains information about the author, editor, and publisher of Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete material.
Select “Donate & Download,” on top of “Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete” and upon completing your donation, you will be directed to the download page or you can chat with us for alternative donation methods.
You have the opportunity to upload content similar to “Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete” and receive payment for each download of the material. Engage in a conversation with our representative if you have any topics related to Bamboo Leaf Ash As A Partial Replacement Of Cement In Concrete.