List of INDUSTRIAL CHEMISTRY Project Topics and Materials in PDF/DOC:
8 Chapters
|
85 Pages
|
8,424 Words
|
Project
The project aims to develop a flow process to obtain the optimum temperature and time necessary for the maximum recovery of alkali present in palm inflorescence. On this ground, a preliminary experiment was performed. D … Continue reading
6 Chapters
|
54 Pages
|
6,731 Words
|
Project
The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabr … Continue reading
5 Chapters
|
41 Pages
|
3,263 Words
|
Project
This project is concern about the construction of an electrical stove with three oven apartment is described in his project. It was carried out in order to solve the problem often encounter in cooking and drying and at th … Continue reading
5 Chapters
|
44 Pages
|
5,534 Words
|
Project
The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu. The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in … Continue reading
7 Chapters
|
34 Pages
|
3,433 Words
|
Project
This project which is on the design and fabrication of a two face gas burner is a brief exploration on the various ways and means of designing, construction, operating the two face gas burner, putting cost into consideration for economic advantage … Continue reading
6 Chapters
|
34 Pages
|
3,932 Words
|
Project
This project is a fabrication of a standard drawing writing desk using the cheapest, effective and most readily available materials. Method of maintenance and services were also taken into consideration. The functional aspect of the equipment … Continue reading
5 Chapters
|
58 Pages
|
6,645 Words
|
Project
The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel i … Continue reading
5 Chapters
|
53 Pages
|
1,440 Words
|
Project
This project was done to extract and characterize bean oil according to their particle sizes. The experiment was carried out using scent bean (i.e. ‘Ozaki’, ‘Ijilizi’or ‘Azamu’) as sample. The oils were ext … Continue reading
5 Chapters
|
99 Pages
|
12,520 Words
|
Project
This research project was carried out principally for the production of liquid and vapourized perfumes from local raw materials. The local raw material were subjected to various processing conditions in order to obtain purified perfume. Th … Continue reading
5 Chapters
|
59 Pages
|
2,399 Words
|
Project
This research project studied on the kinetics of hydrolysis of cellulose to glucose. The steps employed to achieve this project involved extraction of cellulose from sawdust and subsequently, hydrolysis of starch to simple sugar. Thi … Continue reading
6 Chapters
|
54 Pages
|
7,461 Words
|
Project
Blender is an electric machine for size reducing soft food or liquid mixture. Blender is some time called liquidizer consists of a glass jar or jug containing a steel blade assembly at the base driven by a small electric motor. Construction of blender was d … Continue reading
7 Chapters
|
47 Pages
|
5,369 Words
|
Project
The production and analysis of “Ngu†extract for temperature and water requirement for leaching of casuistic alkali is the basic objective of this project. The production was carried out by using unit oper … Continue reading
8 Chapters
|
53 Pages
|
3,751 Words
|
Project
The fabrication of a pressurized kerosene oven. This project has been fabricated with special economical needs for the small scale baking industries, wholesalers and distributors who import this type of baking oven from outside the country … Continue reading
5 Chapters
|
83 Pages
|
12,030 Words
|
Project
This project was carried out using acid activated coal from Enugu coal and the production of ve4getablew oil was monitored using spectrophotometer to measure the absorbance. It was also perform to check the suitability of activated Enugu coa … Continue reading
5 Chapters
|
69 Pages
|
1,438 Words
|
Project
Air pollutions pollutant showed that the extent of spreading depends on the motor vehicle traffic population of the area. This pollution strongly generated through combustion of fos … Continue reading
8 Chapters
|
92 Pages
|
12,200 Words
|
Project
The production of the soap was carried out using all the necessary equipments like the reactor, mould, stirrer, hygrometer guage etc. and all the required reagents for soap production in correct proportion. In the production, palm kernel oil … Continue reading
5 Chapters
|
100 Pages
|
12,650 Words
|
Project
Palm kernel, coconut and melon oils were extracted and refined. Their physical and chemical characteristics were examined. The refined oils were blended to produce three samples of margarine: palm kernel oil ma … Continue reading
5 Chapters
|
52 Pages
|
1,709 Words
|
Project
This study was on oxidative stress status of rat fed with Pentraclethra macrophylla, otherwise known as African oil bean seed oil in English or Ugba in Igbo. Sixteen male rats were distributed into four groups. 1 (control), t … Continue reading
5 Chapters
|
46 Pages
|
6,828 Words
|
Project
Wheelbarrow can be defined as a machine that is used by labourers, farmes, gardeness, and others for transporting loads to heavy by hand it from one place to another. However, materials used for construction purpose are bought in standard sizes wither in … Continue reading
8 Chapters
|
72 Pages
|
8,771 Words
|
Project
This research project is aimed at producing domestic powder and consequently, three different types of powder were produced, namely, simple face powder (pan-cake), medicated/Antiseptic powder (dristing powder). During the various production Talcum, Zinc … Continue reading
4 Chapters
|
56 Pages
|
6,588 Words
|
Project
This project (Construction Of A Simple Size Reduction Machine) It was constructed locally with the use of local materials and tools in I.M.T mechanical Engineering workshop. The various parts of the equipment were constructed separatel … Continue reading
8 Chapters
|
80 Pages
|
10,247 Words
|
Project
Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs. Generally, interface is a boundary layer, so the bo … Continue reading
5 Chapters
|
88 Pages
|
8,359 Words
|
Project
INTRODUCTION The most common type of heat exchanger used in industry contains a number of parallel tubes enclosed in a shell and is thus called a shell and tube heat exchanger. These heat exchangers are employed when a … Continue reading
5 Chapters
|
30 Pages
|
3,758 Words
|
Project
Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spri … Continue reading
5 Chapters
|
48 Pages
|
277 Words
|
Project
Cola nitida has been in use in the eastern parts of Nigeria for the management of certain ailments and as an aphrodisiac in the management of some sexual dysfunctions. However the effects … Continue reading