Construction Of Turbine Mixer
INSTRUCTIONS:
- You are perusing the project material titled “Construction Of Turbine Mixer.”
- The project material on Construction Of Turbine Mixer is available for instant download.
- Preview Chapter One of Construction Of Turbine Mixer at no cost.
- To access the complete project material for Construction Of Turbine Mixer, kindly make a donation to support the ongoing maintenance and operation of this website.
- The provided work on Construction Of Turbine Mixer is intended solely for academic research purposes and should be utilized strictly as a set of guidelines.
- Our objective in distributing Construction Of Turbine Mixer is to aid individuals unfamiliar with project research, specifically writers seeking assistance in this area.
- Kindly refrain from directly replicating the content provided in Construction Of Turbine Mixer materials.
- Feel free to reference “Construction Of Turbine Mixer” in your work, provided that you paraphrase appropriately.
- Unauthorized reproduction of Construction Of Turbine Mixer content is prohibited under our Terms of Use.
- UniProjects assumes no responsibility if you replicate the content of this Construction Of Turbine Mixer.
The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu.
The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which they will be used in, making out, cutting out to sizes, rolling folding, welding, body – filling, filling, glass – papering and painting. The total surface area is 10741.5CM2
The first step taken in the fabrication of ht said project was the selection of the material suitable for the construction.
The materials used in the construction were locally sourced and were selected to suit the desired purpose. The mild steel was used instead of galvanized steel due to its relative low cost.
The mild steel was located with paint to prevent corrosion attack and deterioration of the work.
The dimensions of the project were as follow 31.0CM. for the height and –21.0cm for the diameter. The volume [capacity] of the cylinder is 10,74 1.5cm3 the average speed of the turbine mixer is 125pm. The turbine mixer is manually operated a design that is meant to save cost.
Title page
Letter of transmittal
Approval page
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0 Introduction
1.1 Objectives / scope of the project
CHAPTER TWO
2.0 Literature review
2.1 Agitation and mixing
2.2 Liquid – liquid agitation
2.3 Purpose of agitation
2.4 Types of mixer / mixing equipment
2.5 Application of impeller
2.6 Shaft
2.7 Baffles
2.8 Circulation rates
2.9 Mixers for plastic solids and pastes
2.10 Mixers for dry light solids [powder]
2.11 Material of construction.
CHAPTER THREE
3.0 Fabrication / modification procedure
3.1 Steps of fabrication process
3.2 Cost analysis.
CHAPTER FOUR
4.0 Discussion
4.1 Conclusion
4.2 Recommendation
4.3 Reference
4.4 Nomenclature
CHAPTER FIVE
DISCUSSION
CONCLUSSION
RECOMMENDATION
REFERENCES
APPENDIX / NOMENECLATURE
INTRODUCTION
The multiple of process and mechanical variable makes fluid agitation one of the most complete unit operations. For this reason the systematic studies of underlined me chemise of mixing operation progressed slowly, quantitative design data is spores and almost innumerable agitator configuration have evolved. Though often confused, agitation and mixing are not synonymous. Agitation refers to the induced motion of a material in a specified way, usually in a circulatory pattern inside some sort of container. Mixing is the random distribution into and through one another of two or more initially separate phases. Ex A single homogeneous material such as a thankful of cold water can be agitated, but it cannot be mixed until some other material is added such as powdered soerd.
However, many processing operations depend to their success on the effective agitation and mixing of fluids. To enhance these processing operation, Experimental agitators were developed to serve a wide variety of poetical and fundamental fluid mixing problem.
Experience has revealed that reaction that recurred mixing and agitation most often cannot perform without agitators. That is why the need to discuss agitators, Agitations and mixing can not be over ruled and has to be given to student in the territory institution as project work.
Mixing is been used to perperon on uniform combination of two or more substances. The material fed to a mixer could be gasses, higuidion solids. The product that is from mixer may be homogeneous or heterogeneous substance.
THE OBJECTIVE AND THE SCOPE OF THE PROJECT
Turbine mixer is one of the important equipment found in the chemical industries. It is been applied in variety of operations in the industries and homes such as mixing of solution of liquids, solids and gases.
The main objective of the project is to construct turbine mixer that will be widely versatile in application / operation.
If you’re referencing specific information, quotes, or ideas from “Construction Of Turbine Mixer”, provide a citation in the appropriate format such as APA, MLA, or Chicago.
The title page of downloaded document contains information about the author, editor, and publisher of Construction Of Turbine Mixer Project material.
Select “Donate & Download,” on top of “Construction Of Turbine Mixer” and upon completing your donation, you will be directed to the download page or you can chat with us for alternative donation methods.
You have the opportunity to upload content similar to “Construction Of Turbine Mixer” and receive payment for each download of the material. Engage in a conversation with our representative if you have any Project topics related to Construction Of Turbine Mixer.