Design And Construction Of An Automatic Battery Charger ABC
INSTRUCTIONS:
- You are perusing the project material titled “Design And Construction Of An Automatic Battery Charger ABC.”
- The project material on Design And Construction Of An Automatic Battery Charger ABC is available for instant download.
- Preview Chapter One of Design And Construction Of An Automatic Battery Charger ABC at no cost.
- To access the complete project material for Design And Construction Of An Automatic Battery Charger ABC, kindly make a donation to support the ongoing maintenance and operation of this website.
- The provided work on Design And Construction Of An Automatic Battery Charger ABC is intended solely for academic research purposes and should be utilized strictly as a set of guidelines.
- Our objective in distributing Design And Construction Of An Automatic Battery Charger ABC is to aid individuals unfamiliar with project research, specifically writers seeking assistance in this area.
- Kindly refrain from directly replicating the content provided in Design And Construction Of An Automatic Battery Charger ABC materials.
- Feel free to reference “Design And Construction Of An Automatic Battery Charger ABC” in your work, provided that you paraphrase appropriately.
- Unauthorized reproduction of Design And Construction Of An Automatic Battery Charger ABC content is prohibited under our Terms of Use.
- UniProjects assumes no responsibility if you replicate the content of this Design And Construction Of An Automatic Battery Charger ABC.
The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure developed cover the construction of battery charger for battery sizes ranging from 6 volts to 12 volts.
The phototype of a battery charger for these ranges of battery has been implemented following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory.
Adequate care has been taken in the design and construction to ensure that the resultant battery charger is both reliable and easy to use.
Title Page
Certification
Dedication
Acknowledgement
Abstract
Chapter One
1.0 Introduction
Chapter Two
2.0 The Storage Battery
2.1 Battery
2.2 The Storage Battery Accumulator
2.3 Nickel – Iron (Nife) Accumulator
2.4 Lead – Acid Accumulator
2.5 Active Material Of Lead – Acid Cell
2.6 Lead Peroxide (Pbv2)
2.7 Sponge Lead (Pb)
2.8 Dilute Sulphric Acid
2.9 Chemical Changes
2.10 Discharging Of A Battery
2.11 Indication Of A Fully Charged Cell
2.12 Casing
2.13 Voltage
2.14 Specification Gravity Of The Electrolyte
Chapter Three
3.0 Power Supply Unit
3.1 Component Of The Power Supply Unit
3.2 Ac – Dc Rectification
3.3 Automatic Cut Off Circuit
Chapter Four
4.0 The Battery Charging
4.1 Method Of Charging
4.2 Constant – Voltage Method
4.3 Operation Of The Charger
4.4 Battery Charger’s Casing
Chapter Five
5.0 Summary, Conclusion And Suggestion For Further Improvement
5.1 Summary
5.2 Conclusion
5.3 Cost Of Production
References
A battery charge is an electrical device employed in charging batteries. The batteries that are usually charged by battery chargers are the storage batteries also known as “accumulatorsâ€.
The charger is made up of various Electrical and Electronic component, which for the purpose of clarity are grouped with four basic unit;
They are;
The power supply unit
The smoothing circuit
The regulatory unit and
The regulated D.C charging unit
Battery chargers comes in various designs and voltage. The choice of a particular kind of charger that depends largely on the size of battery or batteries which one intends to charge. The miniature battery charger could be needed to charge batteries whose voltage ranges from 6-12 volts. The bigger battery chargers are for batteries with voltage ranging 12 – 48 volts. These are the heavy duty batteries.
The battery charger is built in such a way that it delivers a constant value of d.c current into the battery it is charging is the opposite direction from which current flows on the batteries during discharge. One cannot successfully design a battery charger without fundamental understanding of the accumulator because it also makes up the operation. Thus chapter two aimed at a brief study of the accumulator (accumulator). Chapter three deals with the power supply unit, which senses as the backbone of the battery charger and how the automated cut off is achieved. Chapter four full analysis’s the operation of a battery charger and its casing while chapter five which happen to be the last chapter aimed at concluding and summarizing what has been achieved at the and of the project.
If you’re referencing specific information, quotes, or ideas from “Design And Construction Of An Automatic Battery Charger ABC”, provide a citation in the appropriate format such as APA, MLA, or Chicago.
The title page of downloaded document contains information about the author, editor, and publisher of Design And Construction Of An Automatic Battery Charger ABC Project material.
Select “Donate & Download,” on top of “Design And Construction Of An Automatic Battery Charger ABC” and upon completing your donation, you will be directed to the download page or you can chat with us for alternative donation methods.
You have the opportunity to upload content similar to “Design And Construction Of An Automatic Battery Charger ABC” and receive payment for each download of the material. Engage in a conversation with our representative if you have any Project topics related to Design And Construction Of An Automatic Battery Charger ABC.