Design And Installation Of 200 Watt Solar Power System
INSTRUCTIONS:
- You are perusing the project material titled “Design And Installation Of 200 Watt Solar Power System.”
- The project material on Design And Installation Of 200 Watt Solar Power System is available for instant download.
- Preview Chapter One of Design And Installation Of 200 Watt Solar Power System at no cost.
- To access the complete project material for Design And Installation Of 200 Watt Solar Power System, kindly make a donation to support the ongoing maintenance and operation of this website.
- The provided work on Design And Installation Of 200 Watt Solar Power System is intended solely for academic research purposes and should be utilized strictly as a set of guidelines.
- Our objective in distributing Design And Installation Of 200 Watt Solar Power System is to aid individuals unfamiliar with project research, specifically writers seeking assistance in this area.
- Kindly refrain from directly replicating the content provided in Design And Installation Of 200 Watt Solar Power System materials.
- Feel free to reference “Design And Installation Of 200 Watt Solar Power System” in your work, provided that you paraphrase appropriately.
- Unauthorized reproduction of Design And Installation Of 200 Watt Solar Power System content is prohibited under our Terms of Use.
- UniProjects assumes no responsibility if you replicate the content of this Design And Installation Of 200 Watt Solar Power System.
The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective gadgets like cut out switches; to give the 200W expected. The solar panel was mounted outside the building to allow for maximum collection of sun energy. It is expected that the system will help the department meet up with its office duties even when central power is not available.
Title Page
Approval page
Dedication
Acknowledgement
Abstract
Table of content
List of figures
List of tables
CHAPTER ONE:
1.0 INTRODUCTION
1.1 Need for the project
1.3 Scope of study
1.4 Definition of terms
CHAPTER TWO:
2.0 LITERATURE REVIEW
2.1 The basics of solar power system
2.2 Principle of solar panel
2.2.1 Estimating system out
2.2.2 Standard test conditions
2.2.3 Temperature
2.2.4 Dirt and dust
2.2.5 Mismatch and wiring losses
2.3 Solar charge controller
2.4 Principle of inverter
2.4.1 Inverter sizing
2.4.2 DC to AC conversion losses
2.5 solar battery
2.5.1 Temperature effect
2.5.2 Battery voltage
2.5.3 Battery power conversion efficiency
2.5.4 Monitoring and maintenance
CHAPTER THREE:
3.0 SYSTEM OPERATION
3.1 Block diagram of the system
3.2 System operation with block diagram
CHAPTER FOUR:
4.0 SYSTEM DESIGN
4.1 Load evaluation and power consumption table
4.1.1 Calculating power consumption
4.2 Battery sizing
4.3 Solar panel sizing
4.3.1 Typical Pv electrical system types
4.3.2 Solar array sizing worksheet
CHAPTER FIVE:
5.0 PROCUREMENT AND INSTALLATION
5.1 Procurement
5.2 Determination of installation site
5.2.1 Mounting options
5.3 Installation procedure
CHAPTER SIX:
6.0 TEST AND RESULT
6.1 Test and results
CHAPTER SEVEN:
7.0 CONCLUSION AND RECOMMENDATION
7.1 Conclusion
7.2 Recommendation
7.3 Limitation
Reference
INTRODUCTION
1.1 NEED FOR THE PROJECT
The general objective of the system is to provide efficiency, steadiness in the use of power appliances, by ensuring continuous availability of power supply even in the absence of mains. Uninterruptability of the system made it possible to eliminate all suspense from mains outage during the execution of an important and urgent assignment as may be required.
For better production of the system, the system was operated at a fully charged condition of the battery.
The project was rated 200W of 220V and 50Hz. It was expected that at this condition, it was favourable to carry load of the stipulated power. Loads of low power factors are not helpful since they produce spikes. Overloading is not potent to provide zero change over time and the inverter had LEDs which indicates mains failure and battery discharge and system fault.
1.2 SCOPE OF STUDY
This solar power source makes it possible to provide a clean reliable supply of alternative electricity free of sags or surges which could be found in the line voltage frequency.
The solar power system (SPS) system achieved this by direct current from solar panel and by rectifying the standard main supply, using the direct current to charge the batteries and to provide clean alternative power by passing the energy a filter system.
It has zero change over time and LEDs which indicates mains fail and battery discharge level and it provides 100% protection against line noise, spikes surges and audio frequency interference.
1.3 DEFINITION OF TERMS
1. Inverter unit: This unit converts a DC voltage into AC voltage with the help of the inverter unit.
2. Automatic Control Unit: This provides all the required control needed to meet up the objective of the whole system
3. Battery Unit: This is a secondary cell unit, capable of storing enough DC voltage from either sun or AC main, of which is later converted to AC voltage.
If you’re referencing specific information, quotes, or ideas from “Design And Installation Of 200 Watt Solar Power System”, provide a citation in the appropriate format such as APA, MLA, or Chicago.
The title page of downloaded document contains information about the author, editor, and publisher of Design And Installation Of 200 Watt Solar Power System Project material.
Select “Donate & Download,” on top of “Design And Installation Of 200 Watt Solar Power System” and upon completing your donation, you will be directed to the download page or you can chat with us for alternative donation methods.
You have the opportunity to upload content similar to “Design And Installation Of 200 Watt Solar Power System” and receive payment for each download of the material. Engage in a conversation with our representative if you have any Project topics related to Design And Installation Of 200 Watt Solar Power System.