List of MECHANICAL ENGINEERING Project Topics and Materials in PDF/DOC:
6 Chapters
|
31 Pages
|
3,301 Words
|
Project
Fields:
The project is about fabrication of wheel-barrow, which is fabricated in Mechanical Engineering workshop in Institute of Management and Technology, Enugu. The report comprises seven chapters. Chapter one is about the introduction of the wheel. C … Continue reading
ABSTRACTThis work is on an industrial wheelbarrow. An industrial wheelbarrow is a small hand-propelled vehicle, usually with just one wheel, designed to be pushed and guided by a single person using two handles to … Continue reading
Fields:
TABLE OF CONTENTSCOVER PAGETITLE PAGEAPPROVAL PAGEDEDICATIONACKNOWLEDGEMENTABSTRACTCHAPTER ONEINTRODUCTION1.1Â Â Â Â Â BACKGROUND OF THE PROJECT PROBLEM STATEMENT OBJECTIVE OF THE STUDY SIGNIFICANCE OF THE STU … Continue reading
ABSTRACTWhen a motor fails, the user must decide whether to repair or replace it. To make a proper decision, one must consider the cost of the repair, the availability of a replacement, the age of the motor, the e … Continue reading
ABSTRACTGroundnut shelling machine was designed and fabricated at the department of Mechanical Engineering, institute of Technology, Kwara State Polytechnic Ilorin aimed at increasing shelling/decorticating effici … Continue reading
ABSTRACTBurglar proofs are major essential application to building structure activities for the beautification and security of the house such as school subtraction detached garage and high durability the ability t … Continue reading
CHAPTER ONE INTRODUCTIONIn the past with the necessary of metals it always seems impossible to join two metals together with grooving riveting, this idea leads to alternative of finding a lasting solution to the … Continue reading
5 Chapters
|
49 Pages
|
5,444 Words
|
Project
Wheelbarrow is a simple machine, which belong to the second-class lever. This is because the load or resistance is placed between the effort and the fulcrum. It is used in many areas of work to convey loads that are too heavy or bulky to be ca … Continue reading
ABSTRACTThe main aim of this project is to fabricate a semi-automated Can Crusher machine to reduce the scrap volume and use the Cans so that carrying them to the recycle site becomes easy. Now-a- days, a large nu … Continue reading
5 Chapters
|
31 Pages
|
3,669 Words
|
Project
Fields:
Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet. Precisely mild steel sheets. … Continue reading
5 Chapters
|
46 Pages
|
6,828 Words
|
Project
Wheelbarrow can be defined as a machine that is used by labourers, farmes, gardeness, and others for transporting loads to heavy by hand it from one place to another. However, materials used for construction purpose are bought in standard sizes wither in … Continue reading
TABLE OF CONTENTTitle page                                                                                             … Continue reading
6 Chapters
|
63 Pages
|
7,931 Words
|
Project
Fields:
This project is aimed at producing an oven a purposeful baking oven with temperature regulator, which is economical and very convenient to use. The equipment was designed taking into consideration the case of its production, maintenance and ser … Continue reading
ABSTRACTMethanol is a clear liquid chemical that is water soluble and readily biodegradable. Methanol is comprised of four parts hydrogen, one-part oxygen and one-part carbon, and is the simplest member of a group … Continue reading
5 Chapters
|
35 Pages
|
4,924 Words
|
Project
Fields:
Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine ma … Continue reading
5 Chapters
|
33 Pages
|
4,215 Words
|
Project
Fields:
In the society at large Technology is fast replacing the crude method of carrying out work and has been making room for employment. Besides, it has also caught the attention of the youths who will prefer to work in … Continue reading
5 Chapters
|
64 Pages
|
11,470 Words
|
Project
Fields:
1.1 INTRODUCTION Hydrodynamic journal bearings are typical critical power transmission components that carry high loads in different machines. In machine design, therefore, it is essential to know the true or expe … Continue reading
5 Chapters
|
58 Pages
|
5,682 Words
|
Project
Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy. Also studies we … Continue reading
TABLE OF CONTENTCOVER PAGEAPPROVAL PAGEDEDICATIONACKNOWLEDGEMENTTABLE OF CONTENT INTRODUCTION BREIEF HISTORY AND HISTORICAL BACKGROUND LITERATURE REVIEW OBJECTIVES OF THE PRESENT WORK SCOPE OF ELECTRICC ARC W … Continue reading
ABTRACTThis work is on fabrication of a low-cost spot-welding machine for students in higher institutions. The major factors controlling this process are current, time, electrode force, contact resistance, propert … Continue reading
CHAPTER ONE1.0Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â INTRODUCTION1.1Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â … Continue reading
ABSTRACTLevels of noise generated from grinding machines were measured. Noise levels as high as 116dB was obtained. These levels of noise can be stressful that can result to fatigue. It is capable of causing tempo … Continue reading
6 Chapters
|
29 Pages
|
4,790 Words
|
Project
Fields:
The air of this project is to design and fabricate a bench shearing machine which can complete favorably with the imported ones. this machine is designed and fabricate, using our cheap and available materials. Some qualities suc … Continue reading
5 Chapters
|
25 Pages
|
2,471 Words
|
Project
Fields:
FLUSHING OF THE CONDENSER The refrigerant gas let into the condenser through the compressor and the vacuum pump was connected to the condenser to absorb dirty. REFILLING OF GAS INTO THE COMPRESSOR Gas was refilled into the compress … Continue reading